How to Install Artificial Turf: Step by Step With a Materials List
To install artificial turf, dig out 3 to 4 in of soil, compact about 3 in of road base or decomposed granite with a slight slope, roll out the turf with blades facing one way, glue seams onto seam tape, nail about every 6 in around the edge, then brush in 1 to 2 lbs of infill per sq ft.
What a Good Installation Looks Like
The turf is the part you see, but the base does most of the work. A properly excavated, compacted and graded base keeps the surface flat, drains water and stops the turf from rippling or sinking. Most failures that show up in the first few years, such as dips, puddles and seams lifting, trace back to the base, not the turf.
The steps below follow the order installers use. Specs vary between turf makers, so where the manufacturer of your product gives a number, use theirs. Some warranties only apply if the product is installed to spec.
Step 1: Measure and Plan the Layout
Get the area and the overall dimensions first. You can measure your yard from satellite for the square footage and perimeter, then confirm the key dimensions with a tape. Turf comes in rolls, commonly 15 ft wide, so plan how the strips will run and where the seams will fall before you order. Our guide on how to measure for artificial turf walks through strip and waste math.
Step 2: Remove the Lawn and Excavate
Strip the existing grass and dig out soil to make room for the base. Installation guides commonly call for removing about 3 to 4 in. On heavy clay that drains poorly, some manufacturers recommend digging deeper, at least 4 in and in some cases around 7 in, to fit a thicker base.
- Cap or lower sprinkler heads inside the turf area.
- Set a rough grade that falls away from the house.
- Compact the native soil before adding anything on top.
Plan for disposal. Excavated soil adds up quickly, and loosened soil takes up more room in a trailer than it did in the ground.
Step 3: Weed Barrier (Optional)
A porous weed barrier fabric laid over the excavated soil helps keep weeds from coming up through the base. If you have burrowing pests, some installers add gopher wire at this stage. Use a very porous fabric so it does not slow drainage. If dogs will use the turf, talk to your installer first: at least one installation guide advises against weed fabric under pet turf. See our guide to artificial turf for dogs.
Step 4: Spread and Compact the Base
The usual base is class II road base, crushed rock or decomposed granite. Installation guides commonly specify 2 to 3 in, and many installers use about 3 in compacted. A rule of thumb from one installation guide: one cubic yard of base covers about 100 sq ft at 3 in deep, and a cubic yard weighs roughly a ton.
- Spread the base in layers rather than all at once. One manufacturer recommends compacting every 4 in or after each layer, and warns that layers of 2 in or less can crack after compaction.
- Lightly wet the base, then compact it with a plate compactor or roller. One guide specifies compacting to 90%.
- Grade a slight slope for drainage. A minimum fall of about 1% is a common spec, with 1 to 2% often recommended.
- Finish the base about 1 in below the edge of adjoining patios or walks, so the turf sits flush.
- Smooth out every footprint and ridge. Any bump in the base shows through the turf.
Step 5: Lay, Cut and Seam the Turf
Unroll the turf and let it sit in the sun for 30 minutes to 2 hours. The backing relaxes and wrinkles flatten, which makes it easier to stretch and cut. Carry it into place rather than dragging it across the base.
- Grain: every piece must have its blades facing the same direction, or the seams show as a color change. Installers commonly point the blades toward the house.
- Cutting: cut from the back with a carpet knife so you can follow the stitch rows. Leave about 1/4 to 1/2 in extra at borders to tuck in later.
- Seaming: trim both edges cleanly along a stitch row and butt them together without overlapping, leaving the same gap as the spacing between stitch rows. Center seam tape under the joint, apply turf adhesive to the tape following the maker's directions, then press the edges down. Setting infill bags along the seam while the glue sets helps it bond.
- End seams: if strips are joined end to end, stagger those joints so they do not line up.
Step 6: Nail the Perimeter and Field
Fasten the turf with turf nails or staples, commonly 5 to 6 in long. Start at one end, stretch the turf taut and work toward the other end. Specs vary: one installation guide calls for a nail every 6 in along the perimeter and every 2 ft across the field, while another calls for 3 to 4 in at the edges and 12 to 24 in across the field. Add extra nails along seams.
Part the blades before each nail so you do not pin fibers down, and do not drive nails so deep they leave a dimple. Tuck the extra edge into the border with a putty knife.
Step 7: Brush, Infill and Groom
Brush the turf with a power broom or stiff push broom to stand the fibers up. Spread infill with a drop spreader in several light passes, brushing between passes so it settles down into the pile. Most artificial grass takes 1 to 2 lbs of infill per sq ft; the infill guide covers rates and types. Finish with a final brushing and a rinse.
Materials List for a 500 sq ft Lawn
Example: a 20 x 25 ft rectangle, 500 sq ft, with a perimeter of 2 x (20 + 25) = 90 ft. The turf comes in 15 ft rolls, laid as two strips side by side across the 25 ft side.
| Item | Math | Quantity |
|---|---|---|
| Soil to excavate (4 in) | 500 x 0.33 ft = 167 cu ft / 27 | About 6.2 cu yd in the ground |
| Base, 3 in compacted | 500 / 100 sq ft per cu yd | About 5 cu yd, roughly 5 tons |
| Weed barrier (optional) | Area plus overlaps | About 550 sq ft |
| Turf, 15 ft wide | 25 / 15 = 1.67, so 2 strips of 20 + 1 ft trim = 21 ft | 42 linear ft (630 sq ft) |
| Seam tape | One seam, 20 ft long | About 22 to 25 ft |
| Seam adhesive | 20 ft of seam | Check the coverage on the adhesive label |
| Perimeter nails at 6 in | 90 ft x 2 per ft | 180 |
| Field nails at 2 ft | 500 / 4 sq ft per nail | 125 |
| Seam nails | Reinforcement along 20 ft | About 20 to 40 |
| Infill | 500 x 1 to 2 lbs | 500 to 1,000 lbs, 10 to 20 bags of 50 lb |
| Bender board or edging | Edges not against hardscape | Up to 90 ft |
Laying the strips the other way, across the 20 ft side, would take two 26 ft strips: 52 linear ft, or 780 sq ft of turf for the same lawn. The layout above saves 150 sq ft. Total nails come to about 325 to 345; buy a few extra. If your yard is uneven, order a little more base, since filling low spots uses more than the rule of thumb.
Tools: sod cutter (rentable), shovels, wheelbarrow, grading rake, plate compactor, carpet knife and spare blades, carpet kicker, hammer, drop spreader, and a power broom or stiff broom. For a full price breakdown, see how much artificial turf costs.
Frequently Asked Questions
How deep do you dig for artificial turf?
Installation guides commonly call for about 3 to 4 in, enough for a compacted base of 2 to 3 in plus grade. Poorly draining clay may need deeper excavation and a thicker base.
What base do you use for artificial turf?
Class II road base, crushed rock or decomposed granite, wetted and compacted with a plate compactor and graded with a slight slope for drainage. One cubic yard covers about 100 sq ft at 3 in.
How far apart do you nail artificial turf?
Common specs run from about 3 to 6 in along the perimeter and 1 to 2 ft across the field, with extra nails along seams. Follow the turf maker's spec when it gives one.
Do you need a weed barrier under artificial turf?
It is optional but common for decorative lawns. Use a very porous fabric, and ask your installer before using one under turf for dogs, since some guides advise against it there.