Measuring Irregularly Shaped Lawns
Tips and techniques for accurately measuring L-shaped, curved, and complex lawn areas using satellite imagery.
Why Irregular Shapes Are Tricky
A perfectly rectangular lawn is easy to measure: length times width. But most real-world lawns have curves, angles, odd corners, and interruptions. Driveways cut through the middle, flower beds carve out irregular sections, and property lines rarely follow straight lines.
Traditional methods like the "break it into rectangles" approach work on paper but are tedious and still leave gaps. Satellite polygon measurement handles any shape naturally because you trace the actual boundary, however complex it is.
Drawing Irregular Boundaries
When tracing an irregular shape in TurfMeasure, focus on following the actual lawn edge:
- Draw slowly along curves. The freehand drawing tool captures more points when you move slowly, which gives you a smoother initial trace on curved sections.
- Don't worry about perfection on the first pass. After your initial trace, TurfMeasure creates an editable polygon with vertex handles. You'll refine the shape next.
- Start at a corner. Begin your trace at a sharp corner or other obvious landmark so you have a clear reference point when the shape closes.
Adding Vertices for Accuracy
After your initial drawing, the polygon will have relatively few vertices. This is fine for straight edges but leaves gaps on curves. Here's how to improve accuracy:
- Find the small midpoint dots between each pair of vertices. These appear as faded green dots halfway along each edge.
- Drag a midpoint dot to where the lawn edge actually is. This creates a new vertex and splits the edge into two segments.
- Repeat along curves. For a curved driveway or round flower bed, you may need 4-6 extra vertices to follow the curve accurately.
- Double-tap to remove any vertex that's not needed (minimum 3 vertices required).
More vertices along curves = more accurate measurement. For straight edges, two end vertices are sufficient.
Handling L-Shaped and Split Lawns
Some properties have lawns split into separate sections by driveways, walkways, or structures. You have two approaches:
Option 1: One large polygon with exclusions
Draw a single polygon around the entire property, then use "Exclude Area" to subtract the driveway, house, walkways, and other non-lawn features. This is usually faster and gives you a total area automatically.
Option 2: Multiple separate polygons
Use "Add Another Area" to draw separate polygons for each lawn section (front yard, back yard, side strip). This is better when you need to know the area of each section individually, such as when different sections need different treatments.
Both approaches give you the same total area. Choose based on whether you need per-section breakdowns.
Curved Edges and Round Features
Common curved features that need extra attention:
- Curved driveways: Add 4-6 vertices along the curve for accurate exclusion
- Round flower beds: Use 6-8 vertices to approximate the circle when excluding
- Meandering property lines: Follow the natural curve with extra midpoint pulls
- Pool areas: Trace the pool edge carefully and exclude it from the lawn area
- Cul-de-sac frontage: The curved street edge needs 3-4 extra vertices
A circle approximated with 8 vertices is accurate to within about 2%. With 12 vertices, accuracy improves to within 0.3%. You don't need perfection, just enough points to follow the general curve.
When to Zoom In
Zoom level dramatically affects how precisely you can place vertices. For irregular shapes:
- Zoom in before drawing for the most accurate initial trace
- Zoom in further when adjusting individual vertices along complex edges
- Use the brightness slider at high zoom to see edges hidden by shadows
- Zoom out occasionally to check that the overall shape looks right
TurfMeasure supports zoom level 21, which shows individual yard features clearly. Don't try to measure a complex property at zoom level 17 or 18 since you won't be able to see the edges accurately enough.
Accuracy Tips for Complex Shapes
- Focus your vertex effort on curves, not straight edges
- After adjusting, check the area number, a few-percent change means you moved something significantly
- Use edge distance labels to verify key dimensions against known measurements
- If the satellite image is unclear, use the brightness slider before guessing
- For very complex properties, measure sections separately and add them up
- Download a PDF report to review the shape and catch any obvious errors